收藏本站
LE25U20AMB
2-2. Status Register Write
The information in status registers BP0, BP1, and SRWP can be rewritten using the status register write command.
RDY, WEN, bit 4, bit 5, and bit 6 are read-only bits and cannot be rewritten. The information in bits BP0, BP1, and
SRWP is stored in the non-volatile memory, and when it is written in these bits, the contents are retained even at power-
down. "Figure 7 Status Register Write" shows the timing waveforms of status register write, and Figure 20 shows a
status register write flowchart. Consisting of the first and second bus cycles, the status register write command initiates
the internal write operation at the rising CS edge after the data has been input following (01h). Erase and program are
performed automatically inside the device by status register write so that erasing or other processing is unnecessary
before executing the command. By the operation of this command, the information in bits BP0, BP1, and SRWP can be
rewritten. Since bits RDY (bit 0), WEN (bit 1), bit 4, bit 5, and bit 6 of the status register cannot be written, no problem
will arise if an attempt is made to set them to any value when rewriting the status register. Status register write ends can
be detected by RDY of status register read. Information in the status registers can be rewritten 1,000 times (min.). To
initiate status register write, the logic level of the WP pin must be set high and status register WEN must be set to "1".
Figure 7 Status Register Write
Self-timed
Write Cycle
tSRW
CS
WP
tWPS
tWPH
SCK
Mode3
Mode0
0 1 2 3 4 5 6 7 8
8CLK
15
SI
SO
01h
High Impedance
DATA
2-3. Contents of Each Status Register
RDY (bit 0)
The RDY register is for detecting the write (program, erase and status register write) end. When it is "1", the device is
in a busy state, and when it is "0", it means that write is completed.
No.A2097-8/21
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LFDAS12XSIT HARDWARE MC9S12XS 112-PIN
LFXP10E-L-EV BOARD EVAL LATTICEXP10E STD
LH28F008SCHT-TE IC FLASH 8MBIT 85NS 40TSOP
LH28F160S3HNS-TV IC FLASH 16MBIT 100NS 56SSOP
LH28F160S5HNS-S1 IC FLASH 16MBIT 70NS 56SSOP
LH28F320S3HNS-ZM IC FLASH 32MBIT 110NS 56SSOP
LH28F320SKTD-ZR IC FLASH 32MBIT 70NS 48TSOP
LHF00L28 IC FLASH 16MBIT 70NS 48TSOP
相关代理商/技术参数
LE25U20AMBM02-AH 功能描述:闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
LE25U40CFQ-AH 制造商:ON Semiconductor 功能描述:REEL / S-FLASH MEMORY(4M)
LE25U40CMC 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:4M-bit (512K??8) Serial Flash Memory
LE25U40CMC-AH 功能描述:闪存 S-FLASH MEMORY(4M) RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
LE25U40CMCQ00-AH 制造商:ON Semiconductor 功能描述:Flash S-FLASH MEMORY(4M)
LE25U40CQE 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:4M-bit (512K??′8) Serial Flash Memory
LE25U40CQE-AH 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
LE25U40CQES00-AH 制造商:ON Semiconductor 功能描述:S-FLASH MEMORY(4M)